V-8 6.0 High Performance Epoxy System

V-8 6.0 High Performance Epoxy

This two part, high solids, epoxy coating for medium to heavy mill thickness comes as a clear resin or can be pigmented with 6.0 Epoxy & Hybrid Pigment. It is designed as a 2 coat application that can range from 12 – 20 mils thick. V-8 6.0 High Performance Epoxy is intended for concrete floors subjected to abrasion and/or chemical spills, where ease of cleaning, cosmetics, and smoothness are a major consideration.

üHigh Solids

üLow Odor

üMedium to High Build in one coat application

üHigh Gloss; good clarity and color retention

üOutstanding chemical and abrasion resistance

ü13 Color Choices

üFulfills the USDA requirements for incidental food contact

Industrial Flooring

V8 6.0 High Performance Epoxy is an industrial-grade epoxy coating designed for large applications. Factories, warehouses, and airplane hangars are ideal areas for V‐8 6.0 High performance Epoxy because these type of floors take constant abuse and need a high performance coating to protect it.

Recommended Systems

16 mil smooth floor – Apply 8 mils V-8 6.0 (200s.f./gal) by squeegee and back roll to remove squeegee marks. Make sure you do a finish roll from end to end. After first coat is dry (usually 8-10 hours), Apply second coat of 8 mils V-8 6.0 (200 s.f./gal) to 16 mils (100 s.f./gal) using same technique as the first coat.

60 mils high build textured floor - Apply 16 mils V-8 6.0 (100 s.f./gal) by squeegee and back roll to remove squeegee marks. Make sure you do a finish roll from end to end, then after 10-15 minutes broadcast Industrial sand flint until completely white. After first coat is dry (usually 8-10 hours) , clean off excess sand, vacuum, and apply 14 mils V -8 6.0 (125 s.f./gal) using same technique as the first coat. Note: For a smoother floor, sand after the first coat, then apply the top coat.

Physical Properties
Pot Life @ 75°F (24° C) 30 minutes and 50% R. H. If temperature and humidity are higher, the curing will accelerate and the pot life will be shorter.

Cure Rate @ 75°F (24°C)

Foot traffic – 12 hours

Light traffic – 24 hours

Heavy traffic and/or chemical spillage – 72 hours

Recoat time @ 75°F (24°C)

From 12-24 hours. After 24 hours, monitor recoating.
Shelf Life 2 years in an unopened container

Typical Physical Properties:

Hardness (Shore D) ASTM D-2240                         81-85

Bond Strength ASTM D 4541                         >400 psi (2.76 MPa) (100% concrete failure)

Tensile Strength ASTM D 638                           8100 psi (55.8MPa)

Compressive Strength ASTM D 695                           11,700 psi (80.7 MPa)

Impact Resistance ASTM D-2794                         160 in-lbs. (18.1 N-m)

Abrasion Resistance ASTM D-4060                         30-40 mg loss (CS-17 wheel, 1000 cycles, 1000 gm load) Taber Abraser

Flammability ASTM D-635                            Film is self-extinguishing

Slip Resistance Equivalent to ASTM D-2047      Passes

VOC (g/l) ASTM D2369-07                      26.7 g/l

(Above typical values based on cure @ 75°F (24°C)

 

6.0 High Performance Epoxy Color Chart

 

Xtreme Information

News

Services and Locations

Services: Concrete Polishing, Coating, Dyed Concrete, Floor Prep, Industrial and Commercial Floor Coating, ESD Conductive Coating, Tank Lining Coating, Mastic Carpet Glue Removal, Crack and Joint Fillers, Concrete Sealer, Concreted Hardener, Concrete Densifier, National Floor Safety Institute, Colorants, Line Striping, Floor Grinding, Shot Blasting, Decorative Chip Flooring, Vinyl Ester, Epoxy Novolac, StaticSmart. Areas: Western Michigan, Grand Rapids, Holland, Montague, Whitehall, Wyoming, Sparta, Grandville, Byron Center, Walker, Hudsonville, Allendale, Coopersville, Zeeland, Muskegon, Traverse City, Rockford, Caledonia, Lansing, Jackson, Kalamazoo, Grand Haven, South Haven, Benton Harbor, St. Joseph, Michigan.

Site Login